The xTool M1 Air Assist Set is a must-have accessory for any xTool M1 laser engraving machine owner looking to improve their cutting and engraving results. The air assist feature blows air directly at the point of laser contact, helping remove smoke, debris, and heat from the work area. This leads to much cleaner cuts, more precise engraving, and the ability to cut thicker materials. 

In this article, we’ll walk through the entire process of installing an xTool M1 Air Assist Set and show you the incredible difference it makes through side-by-side examples. Let’s get started!

Benefits of the xTool M1 Air Assist Set

Here are some of the top benefits you’ll experience after installing the xTool M1 Air Assist Set:

Neat, Clean Cuts and Engravings

Blowing air directly on the cut point eliminates melted edges, burns, and scorching.

Ability to Cut Thicker Materials

The air blast removes debris so the laser can cut deeper into wood, acrylics, leather, and more.

Longer Lasting Laser Lens 

Keeping smoke, vapor, and debris away from the lens means much less cleaning needed and longer lens lifespan.

Precision Engraving

The constant air stream helps stabilize the laser for incredibly precise engraving work.

Household Friendly

The air assist drastically reduces the smoke and odor created during operation.

Adjustable Air Flow 

Match the air pressure and volume to the material thickness and project needs.

Specification

Unboxing and Getting Familiar with the xTool M1 Air Assist Set

When you first receive your xTool M1 Air Assist Set, carefully unbox all the parts and layout everything included:

• Nozzle holder 
• Cross screwdriver
• Silicone connecting tube
• Tweezers
• Air pump
• Air pump connector
• Filter cotton
• Nozzle components
• 2.5m tube
• Lens mount
• Spare lens
• Short tube clamp
• Sealing rings (spare parts)
• Medium tube clamp
• Long tube clamps

Take a few minutes to get familiar with each part and refer to the manuals so you understand what’s what before jumping into the installation.

Step-by-Step Installation Instructions

Installing the xTool M1 Air Assist Set takes about 10-15 minutes if you follow these step-by-step instructions:

1. Remove the Base Plate

The first step is to turn off and unplug your xTool M1 laser engraver. Then, use the included cross screwdriver to remove the 5 screws holding the base plate in place. Set the base plate and screws aside.

2. Remove the Laser Module 

Carefully slide the laser module out from the machine using the included opening tool. Be very gentle as there is a lens inside that you don’t want to displace. 

3. Install the Lens Mount

Screw the included lens mount onto the laser module opening. Make sure the knobs are parallel with the opening.

4. Attach the Nozzle 

The nozzle has magnets built in so it should just clip right onto the front of the lens mount. 

5. Connect the Hose

Find the side of the hose with the marks on it. This is the end that connects to the nozzle holder. Push it firmly in place. Have the hose come out the back of the machine for now.

6. Install the Nozzle Holder

With the machine flipped upside down, clean the area where the nozzle holder will attach with alcohol. Peel off the adhesive backing and firmly press the nozzle holder in place aligned with the marks. 

7. Adjust the Hose

Make sure the hose can move freely and reach all areas of the engraving/cutting table. Loosen and reposition anything restricting it.

8. Connect Pump and Power Cord

Attach the air pump adapter to the open end of the hose. Then connect the power cord and plug it in. 

9. Reassemble Machine

Carefully replace the laser module, double checking the lens is still intact. Screw the base plate back on. You’re now ready to test!

Testing Out the xTool M1 Air Assist Set

To see the incredible difference the xTool M1 Air Assist Set makes, engrave or cut something first without it turned on. Then, do the exact same test with the air assist running. 

The contrast will be shocking! Engravings done with air assist come out far cleaner and crisper. Cuts have less scorching and melted edges. You’ll immediately see how much of an upgrade this is.

Recommended Settings

To get the most out of your xTool M1 Air Assist Set, start with these air flow settings as a baseline:

Then, adjust the airflow up or down as needed to get clean cuts and engraving. The air pressure should remain stable at 30 kPa.

Tips for Ongoing Use

Here are some handy tips for making the most of your xTool M1 Air Assist Set with regular use:

• For laser engraving/cutting, make sure the nozzle is securely attached to the lens mount.
• When blade cutting or not in use, remove the nozzle and place it in the holder clip.
• Periodically check and clean the air pump filter to prevent clogs.
• If the hose rattles or snags, unwrap it and rearrange it to avoid obstructions.  
• Empty the air pump moisture collector bottle regularly.
• Adjust the position and angle of the nozzle to optimize air flow for each new material.

xTool M1 Air Assist Set – The Game Changer

Installing and using the xTool M1 Air Assist Set takes your laser engraving and cutting to the next level. Crisp, clean results, thicker material cutting,precision engraving, and reduced operating smoke are just a few of the big benefits you’ll experience.

If you own an xTool M1 laser machine, this upgrade is a no brainer. The improvements are instantly obvious from the very first test. While it adds some setup time, the payoff is more than worth it.

Give your projects that professional quality finish by letting the xTool M1 Air Assist Set work its magic. Your engraved and laser cut creations will look better than ever!

User Reviews

:FAQs: