You are currently viewing How to Use the XTool D1 Pro: The Ultimate Guidance

How to Use the XTool D1 Pro: The Ultimate Guidance

The XTool D1 Pro is an excellent desktop laser engraver that can be used by beginners and professionals alike. This versatile machine allows you to engrave and cut various materials like wood, acrylic, leather, paper, and more up to 10mm thick. With the right settings and techniques, you can unleash your creativity with the XTool D1 Pro.

The XTool D1 Pro Unboxing and Assembly

How To Set Up Xtool D1 Pro 40w Laser Engraver 2023

When you first receive your XTool D1 Pro, carefully unbox all the components and check that everything is there. You should have the laser engraver frame and parts, control board, power cord, USB cable, rotary attachment, hex wrench sets, and more. Be sure not to lose any small pieces.

Step-by-Step Assembly Instructions

For Full Assembly Instructions Download Pdf

Assembling the XTool D1 Pro is straightforward if you follow the included instructions. Here is an overview of the main steps:

Attach the Side Plates

The four acrylic side plates slide together to form the main frame. Line up the holes for the screws and use the hex wrench to tighten them in place. Ensure the power switch, power port, and USB port align properly.

Install the Control Board

The control board houses the laser tube driver, motion control system, and more. Carefully mount it to the frame using the provided hardware. Plug in the connections for the x-axis motor and limit switches.

Mount the Gantry and Laser Head

Slide the gantry pieces containing the x-axis rails onto the front and back plates. Attach the laser head to the moving gantry securely using the thumbscrews. Connect the laser module’s wiring harness to the control board.

Attach the Y-Axis Components

Mount the Y-axis timing belts, idler pulleys, and stepper motor similar to the X-axis. Adjust the belt tension and make sure the limit switches are connected properly.

Insert Accessories

Install the air assist nozzle, fume extractor, and camera module if included. Insert the TF card and USB thumb drive for transferring designs.

Software Setup

How To Download Xtool D1 Pro Laser Engraver Software

The XTool D1 Pro is compatible with several different laser engraving and design programs. Here are some of the most popular options:

XTool Creative Space

This free software from XTool lets you easily design projects and control the laser. It includes built-in images and templates for common applications like customizing mugs and phone cases. Placing drawings, adding text, modifying settings, and using the laser are all made simple using XTool Creative Space.


LightBurn offers advanced features perfect for experienced users. It gives you more customization for image and text engraving. You can create and run complex designs with multiple colors, layers, and settings. LightBurn costs around $40 but is worthwhile for complex projects.


LaserGRBL is open-source software compatible with many DIY laser engravers. While not as full-featured as LightBurn, it provides good functionality for free. With LaserGRBL you can import images, set power and speed, and operate the laser engraver.


Inkscape is a powerful free vector graphics program. It allows you to draw and edit vector images, text, and shapes. You can then save your designs as an SVG file and import them into XTool Creative Space or LightBurn to engrave or cut.

Getting Started Engraving and Cutting

Is the XTool D1 Pro 40W the Ultimate Laser Engraver?

Once you have assembled your XTool D1 Pro and installed the software, you are ready to start your first project. Follow these tips when getting started:

Prepare Your Material

The XTool D1 Pro can engrave materials as thick as 10mm. Select your material such as plywood, acrylic, leather, or anodized aluminum. Cut it down to an appropriate size to fit in the laser bed. Apply masking tape or a marker to define the engraving area.

Focus and Align the Laser

Use the focus gauge tool to properly focus the laser head at the material surface. Jog the laser head to your defined origin corner and lower it until slightly touching the material. Set this as your home position in the software.

Import or Create a Design

Import a JPEG, PNG, SVG, or other image file into your software. Alternatively, use the built-in tools to create text labels, shapes, and drawings to engrave. Size and position the design within your marked engraving area.

Configure Laser Settings

Determine the correct speed, power, and other settings for your chosen material. Refer to laser setting guides and perform test engraves to dial this in. Using optimized settings helps achieve clean results.

Double-Check File, Focus, and Origin

Before starting the job, carefully verify your design position, laser focus, and origin alignment. Confirm the file path to your design is correct. Then click start to begin engraving or cutting!

Remove and Clean Up Your Project

Once complete, power down the laser and use pliers or a putty knife to gently pry your project off the laser bed. Clean any soot or marks from engraving using a cloth and alcohol. Apply a finish like wood oil or clear coat if desired.

Helpful Features and Accessories

The XTool D1 Pro has handy features and compatible add-ons that expand its capabilities. Here are some to consider using:

Air Assist

Is the XTool D1 Pro 40W the Ultimate Laser Engraver?

The air assist nozzle blows air across the laser focal point. This removes smoke and debris, helping reduce scorching when engraving sensitive materials like wood. Turn air assist on for better results.

Rotary Attachment

The rotary tool lets you engrave and etch cylindrical objects like glasses, mugs, and bottles. Combined with the right software, it enables full-wraparound designs on curved surfaces.

Pass-through Slot

The pass-through slot on the XTool D1 Pro frame is useful for engraving longer items like guitar necks, bats, and canes without disassembly.

Exhaust Fan

Adding an external exhaust fan improves smoke/debris removal when engraving. This helps reduce fumes and keeps the optical path clear for crisp, clean cuts.

Jog Buttons

The manual jog buttons on the laser head let you precisely position the laser without a PC connection. Use them to set an origin or align to your marked design area.

Camera Module

An integrated camera allows for easy artwork alignment without lowering the laser gantry. Just attach it to the laser head and enable live view in your software.

Materials Settings Guide

Xtool D1 Pro Review: Unleash the Power of Laser Engraving

Choosing the optimal laser speed, power, and other settings is key to achieving great results with the XTool D1 Pro. Follow general guidelines:

Engraving Wood

  • Use lower power around 10-20% and higher speeds for engraving into wood. Go slow on sensitive exotic woods.
  • Watch for scorching on lighter woods like maple and birch. Employ air assist or faster speeds.
  • For deeper engraving, make multiple passes at lower speeds and increased power levels.

Cutting Acrylic

  • Acrylic requires around 50-70% power to cut, moving slower for thicker materials. Use just enough power to melt through.
  • Apply masking tape over the cut lines to reduce scorching and debris. Peel tape off after cutting.
  • Leave the protective film on acrylic during cutting. Remove it afterwards for best clarity.

Engraving Leather

  • Engrave leather at lower power around 20% and medium-high speeds for best results.
  • Avoid high power as it will melt and damage leather. Go slow on delicate leathers.
  • Use a leather preparer or deglazer to clean and prepare the surface pre-engraving.

Etching Anodized Aluminum

  • Anodized aluminum requires very low power at around 5%, but can be etched with just one or two passes.
  • Use a low-tack masking tape pre-etching to define your design area.
  • Color-fill your etched designs on anodized aluminum for extra pop.

Cutting Fabric

  • Lower power levels around 5-15% are best when cutting fabric to avoid melting edges.
  • Place fabric on a hard backing for cutting to avoid backside scorching. Cork or acrylic works well.
  • Move the laser slowly and make multiple passes if needed when cutting thicker fabrics.

Troubleshooting Common Issues

Like any machine, you may occasionally run into problems with your XTool D1 Pro laser engraver. Here are some common issues and their typical solutions:

Laser Has No Power

  • Check that the power cord is firmly plugged into the outlet and power switch is in the ON position.
  • Try connecting the engraver directly to the wall outlet rather than a power strip.
  • Inspect the fuse inside the power socket and replace if blown.

Computer Not Recognizing Laser

  • Confirm the USB cable is securely connected between the PC and the laser engraver.
  • Try reinstalling the driver software and reboot your computer.
  • Plug the laser directly into your computer rather than through a USB hub.

Burns and Discoloration on Material

  • Your laser power may be too high for that particular material. Lower it incrementally and re-test.
  • Increase the laser scanning speed to reduce burning and charring effects.
  • Employ air assist or an exhaust fan to improve ventilation when engraving.

Software Crashing or Freezing

  • Ensure your computer meets the minimum system requirements for your software.
  • Update your computer and software to the latest stable versions available.
  • Try restarting your PC and the XTool D1 Pro to clear any memory issues.

Laser Head Not Reaching Corners

  • Check that the gantry wheels are tightly secured and properly aligned.
  • Inspect the belts for damage or looseness and adjust their taughtness as needed.
  • Lubricate the rails and gantry wheels with silicone spray if they stick when moving.

Inspiring Project Ideas

The XTool D1 Pro opens up endless creative options. Here are just a few inspiring ideas to create with this versatile laser machine:

Engrave Family Memory Board

Make a customized family memory board by engraving names, dates, locations, and phrases onto a large wood plank. Attach photos and other mementos with decorative nails.

Etch Stemless Wine Glasses

Create elegant monogrammed glasses by etching initials or designs onto the sides of stemless wine glasses. Just add your glasses to the rotary attachment.

Personalize Leather Valet Tray

Make his and hers matching leather valet trays with your names or initials engraved in a stylish script font. They also make great personalized gifts.

Cut Acrylic Photo Frames

Create inexpensive DIY acrylic photo frames by laser cutting clear acrylic sheets into custom sizes and designs. Finish the cut edges carefully.

Engrave Pet ID Tags

Ensure your pets get returned home using unique engraved ID tags. Add your phone number and address onto a dog or cat tag made of wood, acrylic, or metal.

Craft Engraved Cutting Boards

Make your own custom wood cutting boards engraved with your last name and simple designs like leaves or geometric shapes for a thoughtful housewarming gift.

Etch Stemware for Events

Add a touch of elegance to weddings or formal occasions by etching the event details or monogram on each guest’s glass stemware.

Cut Leather Wallet Inserts

Create thin leather inserts to organize your wallet with laser cut slots for credit cards, ID cards, coins, bills, and more.

Engrave Yeti Cups

Make ordinary Yeti rambler cups unique by engraving names, monograms, logos, or designs onto the stainless steel. They become personalized gifts.

Also read:
A Step By Step XTOOL D1 Pro 10W Assembly
How To Set Up Xtool D1 Pro 40w Laser Engraver 2023
How to Connect xTool D1 Pro to Wi-Fi

There are so many possibilities with the XTool D1 Pro! Use these tips and project ideas to guide you in mastering desktop laser engraving. With practice and the right techniques, you can create professional-looking pieces. Let your creativity run wild!

how to connect xtool d1 pro to lightburn?

Connect the XTool D1 Pro to your computer via USB cable. Install LightBurn, select the correct laser model, and import your design files. Adjust settings in LightBurn and click “Start” to engrave or cut.

how to connect xtool d1 pro to wifi?

Plug in the XTool WiFi adapter to the USB port. Open the adapter settings, select your network, and enter the password. The XTool software will now connect over WiFi.

how to clean xtool d1 pro laser?

Gently wipe the laser lens with a cotton swab dampened with isopropyl alcohol. Clean the engraving bed with a brush and vacuum. Wipe down the external surfaces with a soft cloth.

is xtool d1 pro worth it?

Yes, the XTool D1 Pro is an excellent desktop laser engraver and cutter perfect for beginners or professionals. It can mark and cut various materials up to 10mm thick.

what is xtool?

XTool is a company that manufactures desktop laser engraving and cutting machines. Their popular XTool D1 Pro is an affordable, versatile hobby laser engraver.

  • How to Use the XTool D1 Pro: The Ultimate Guidance

    How to Use the XTool D1 Pro: The Ultimate Guidance

    The XTool D1 Pro is an excellent desktop laser engraver that can be used by beginners and professionals alike. This versatile machine allows you to engrave and cut various materials like wood, acrylic, leather, paper, and more up to 10mm thick. With the right settings and techniques, you can unleash your creativity with the XTool…

Leave a Reply